Does Dvr Firmware Start and Stop Again
- #1
I try again but I will be shorter this fourth dimension in the description of my problem.
Is there someone that tin can tell me how I can programme my smarphone when SP Flash Tool display this error message: ERROR: status_brom_cmd_send_da_fail (0xC0060003) ?
Encounter attached pic.
Thank you for your help.
Attachments
- #2
- #iii
ane. Unplug your device from pc
2. Open Sp Flash Tool with Administrator privileges
3. Go to Download and put scatter.txt file
iv. Now go to Format and make sure that you have checked Car Format Wink and Format whole except Bootloader , click on Start , wait few 2d and close Confirmation popup.
5. Now go to Download and instead of Download only do Format All + Download .
If not , endeavor so Upgrade just or try to flash with another version of wink tool .
Proficient Luck 
- #4
Finally I found the way to program the smartphone.
- Turn off your mobile telephone
- Press Download (SP Button) in SP Flash Tool
- Press Volume Down on the mobile phone.
- Keep Volume Down pressed and connect to the USB
- Normally SP Flash tool starts to programme and yous tin release the Volume Downward primal.
Hop it will work for you.
- #5
didnt worked for meHello,Finally I found the way to program the smartphone.
- Turn off your mobile phone
- Press Download (SP Button) in SP Flash Tool
- Press Volume Downward on the mobile telephone.
- Keep Volume Downwards pressed and connect to the USB
- Normally SP Flash tool starts to programme and y'all tin release the Book Downwardly cardinal.Hop information technology will work for you.
- #6
So i had the same problem and the solution for me was to agree volume up fundamental equally i was connecting and go along pressing until the red bar is 100% and so after a few seconds release it.
Manifestly i deceit post links but i will re-create the tutorial.
With the phone off:
- Click DOWNLOAD in SP Flash Tool
- Hold VolumeUp on your phone
- Connect the phone while however holding VolumeUp
- Concord VolumeUp a couple of seconds later the red bar gets to 100%
- Release
Credit to GizBeat on chinaphonearena.
- #seven
After following
https://www.getdroidtips.com/wink-stock-firmware-using-sp-flash-tool/
I got the
mistake status brom cmd ship da fail 0xc0060003
message.
I started doing what was said past Teddy Lo, but it was not amend.
I kept my current cession (SP Wink Tools five.1752 started with authoritative manner);
went into format tab, left FORMAT WHOLE EXCEPT BOOTLOADER
clicked on START, then Stop
then in download TAB
in the select menu, choose format+download
click DOWNLOAD button
... got the 0xc0060003 message ...
but ... immediately abolish this popular-upward and reclick on DOWNLOAD asap. So, flash goes fine (DA again with red bar, then, all partitions with yellowish bar).
This mode, I accept been able to reinstall ROM v6 on Oukitel K6000 Plus.
Never had to press downwards or up volume during start-upwardly; merely allow telephone kick; or press voldown+power to stop/restart it, if it is already started somehow. My phone was in orange land, and my system was completely broken (not bootable, non usable). I but had working bootloader and recovery; I tried various other ways to install stock ROM, all failed. I had boot loops and other problems. In the end, I went back to SPFT, and just cancelling and reclicking ASAP on the DOWNLOAD push button did it for me.
Now trying ROM v23 ... (will edit in 1h about it).
... happily for you, my windows crashed, and I had to restart the whole process, so now I can write down the working procedure:
- phone was upwardly with ROM v6 working fine
- phone was plugged on USB
- previously installed VCOM
- could non install Android/Download driver
- Oukitel K6000 Plus
- SPFT 5.1752 started with admin perms
- DA already gear up to MTK_AllInOne_DA.bin
- scratter ... the only file bachelor in the folder containing my new rom (official V23 from Oukitel, downloaded terminal yr, and then forgot where I took it - yes it's one year I am trying to upgrade)
- in the bill of fare, select format all + download
- go in format TAB
- tick Auto format
- tick FORMAT ALL except bootloader
- leave validation unticked
- click on START, wait 5s, click Cease
- back in Download tab
- click DOWNLOAD push button
- printing voldown+power to reboot the phone
- got the pop-up once with mistake 0xc0060003
- immediately cancel the popular-up and reclick DOWLOAD push button
- got the popular-upwardly a second fourth dimension, cancel it a second time, click DOWNLOAD a 3rd fourth dimension
- sweat a lot ... DA over again ... partitions once more, yellow lines ... V23 installed \o/
Some steps may be exist useless or optionnal; this was the raw log/history of what I did to work effectually "fault status brom cmd send da neglect 0xc0060003".
First boot is VERY long ...
- #viii
Hi, guys !
I faund decision for me.
- When y'all opened Flash Tool, next you need choose "Download-agent" DA_PL (not MTK_AllInOne_DA)
it's works for me
- #ix
Howdy, guys !
I faund determination for me.
- When you lot opened Flash Tool, next you demand choose "Download-agent" DA_PL (not MTK_AllInOne_DA)
it's works for me
You saved me a day!
Thanks a lot :practiced: :victory:
- #10
This worked for me and finally unbricked this cheap Leagoo S8 that bricked itself!
You rule.
Thanks.
Hello,Finally I institute the mode to program the smartphone.
- Turn off your mobile phone
- Press Download (SP Button) in SP Flash Tool
- Press Volume Down on the mobile phone.
- Keep Volume Down pressed and connect to the USB
- Normally SP Flash tool starts to program and you lot can release the Book Down cardinal.Hop it will work for you.
- #11
Hello I go on getting this error status da selection 0xc0030003
And I cant find whatsoever info online to fix I am trying to flash a elephone p9000 later on a screen replacement
Any help or advice would be smashing help
- #12
Howdy I keep getting this fault condition da selection 0xc0030003And I deceit notice whatsoever info online to fix I am trying to flash a elephone p9000 later on a screen replacement
Whatever aid or advice would be great help
1. There are two stock ROMs officially available for your device. Are y'all sure yous are using the correct 1?
2. Are yous sure you are using a compatible download agent (DA)? If the default "MTK_AllInOneDA.bin" isn't working, bank check your ROM zip to see if yous have anything else... Maybe DA_PL.bin, DA_SWSEC.bin or DA_SWSEC_CRYPTO20.bin might work for your device.
The error yous are getting makes it clear that y'all are trying to use an incompatible DA.
Look into my suggestions, and if you still get the mistake, I'd recommend you to create a new thread, where you're more likely to get help (and sooner besides).
- #13
Hello I continue getting this mistake status da selection 0xc0030003And I deceit observe whatever info online to set up I am trying to flash a elephone p9000 afterward a screen replacement
Any aid or advice would exist smashing aid
Cheers I am new to android I am thinking your right I demand to expect close at what software it is I think iv been at it all day so I thought I would inquire many thanks
- #fourteen
- #xv
What worked for me ...After post-obit
https://www.getdroidtips.com/flash-stock-firmware-using-sp-flash-tool/
I got the
error status brom cmd transport da fail 0xc0060003
message.I started doing what was said by Teddy Lo, only information technology was not improve.
I kept my current cession (SP Wink Tools v.1752 started with administrative mode);
went into format tab, left FORMAT WHOLE EXCEPT BOOTLOADER
clicked on Get-go, then STOP
and then in download TAB
in the select menu, choose format+download
click DOWNLOAD button
... got the 0xc0060003 bulletin ...
but ... immediately cancel this pop-up and reclick on DOWNLOAD asap. Then, flash goes fine (DA once again with red bar, so, all partitions with yellow bar).This fashion, I have been able to reinstall ROM v6 on Oukitel K6000 Plus.
Never had to press downward or up volume during starting time-up; just let phone boot; or press voldown+power to finish/restart it, if it is already started somehow. My phone was in orange state, and my organisation was completely cleaved (not bootable, not usable). I simply had working bootloader and recovery; I tried diverse other means to install stock ROM, all failed. I had boot loops and other issues. In the end, I went back to SPFT, and just cancelling and reclicking ASAP on the DOWNLOAD push button did information technology for me.
Now trying ROM v23 ... (will edit in 1h about it).
... happily for you, my windows crashed, and I had to restart the whole procedure, so now I can write downwardly the working procedure:
- phone was up with ROM v6 working fine
- phone was plugged on USB
- previously installed VCOM
- could not install Android/Download driver
- Oukitel K6000 Plus
- SPFT five.1752 started with admin perms
- DA already set to MTK_AllInOne_DA.bin
- scratter ... the only file available in the folder containing my new rom (official V23 from Oukitel, downloaded terminal year, then forgot where I took information technology - yeah it'southward one year I am trying to upgrade)
- in the menu, select format all + download
- go in format TAB
- tick AUTO format
- tick FORMAT ALL except bootloader
- leave validation unticked
- click on START, wait 5s, click STOP
- back in Download tab
- click DOWNLOAD button
- printing voldown+power to reboot the phone
- got the popular-upwardly once with error 0xc0060003
- immediately cancel the pop-upwardly and reclick DOWLOAD button
- got the pop-upwards a second time, abolish it a 2d time, click DOWNLOAD a tertiary time
- sweat a lot ... DA again ... partitions again, yellowish lines ... V23 installed \o/Some steps may be be useless or optionnal; this was the raw log/history of what I did to work around "error condition brom cmd send da fail 0xc0060003".
First boot is VERY long ...
did not piece of work
- #xvi
:highfive:
Howdy, guys !
I faund decision for me.
- When y'all opened Wink Tool, next you lot demand choose "Download-agent" DA_PL (not MTK_AllInOne_DA)
it's works for me
- #17
- #xviii
Hullo,
I still accept 0xC0060003 error.
Later the red line fills 100% it will get stuck and within 9 seconds and fails.
someone assist me
my phone is HTC, MT65xx
- #nineteen
Hey guys, For those people out at that place whos' problem stays the same and the to a higher place-given solutions don't work cause I know, it doesn't work in all phones(I've tried information technology several times and stock on the same error). I've been researching this problem and none appears to be the solution that works. From the hints that I've gathered this solution work for me and might be for you too.
Assuming you accept opened the SP flashtool and the scatter file is placed.
i. click download
2. connect your phone
three. list down all the names that acquired your problem and practise it several times
#for me : systeminfo, sutinfo, cda and recovery are the causes.
4. uncheck all the issues until none remains and you're done.
I hope this works on you guys. :practiced:
- #20
Hello , endeavor this :
1. Unplug your device from pc
ii. Open Sp Flash Tool with Administrator privileges
3. Go to Download and put besprinkle.txt file
iv. Now get to Format and make sure that you have checked Auto Format Flash and Format whole except Bootloader , click on First , look few 2nd and shut Confirmation popup.
5. Now go to Download and instead of Download only do Format All + Download .If not , attempt so Upgrade only or attempt to flash with another version of flash tool .
Practiced Luck
SORRY, Merely haven't worked for me, got the same error also while doing format.Please HELP. ACTUALLY i am having lenovo k8 note and till yesterday, it was showing the pop-upwardly that driver haven't installed because device is unplugged just i recall that was due to bad information cable, so i changed that one and at present i am having the error(0xc0060003). Don't know what to do side by side ,Delight HELP.
Similar threads
delvecchiovoinficand.blogspot.com
Source: https://forum.xda-developers.com/t/brom-error-status_brom_cmd_send_da_fail-0xc0060003.3707811/
0 Response to "Does Dvr Firmware Start and Stop Again"
Post a Comment